Seat Alhambra Key Problems
Seat's Jumbo MPV family is among the top in its class when it comes down to resale values. With a new generation model now available, it's better than ever.
There are many reasons the key fob won't function properly, such as an inoperative coin battery or damage to the receiver module or signal interference. This article will walk you through the steps to get it back to working.
seat replacement car key G28 Car Keys
If your key fob for the seat alhambra can withstand an wash cycle, a dip in the water or a pool, it has a waterproof chip. But, you shouldn't do this often, as prolonged exposure to water increases the risk of the key fob being damaged. If the key fob ceases to functioning after exposure to clean water from the tap or rain, just take out the battery, wipe the electronic component with a towel and let it dry completely before putting it back into. If the key fob was exposed to salty or soapy water and salty water, it is recommended you clean the chip with isopropyl or electronic cleaner.
Faulty Receiver Module
If you have tried a new battery for a button and the key fob still does not lock or unlock, it's likely the receiver module has found a fault. The good news is that it is a fairly easy and affordable fix, you can simply remove the battery 12 volts for a few minutes (first take off the negative cable, then press the horn button numerous times) to eliminate any remaining electric current, then reconnect it in reverse order e.g. Positive cable first and then negative.
ESP Warning Light If the ESP warning light flashes, this is normal and means that the car is traveling on terrain that has traction issues between the road surface and the tyres is not ideal like snow, gravel or a lot of surface water. If the ESP warning light is continuously blinking, it indicates that there is a fault within the system. It should be diagnosed using a iCarsoft i908 Seat OBD Code Reader which will give you a specific fault description.
Dead Coin Battery
One of the most frequent reasons for the seat alhambra keys to stop working is a dead battery. The key fob has an insignificant button cell battery that is able to keep it powered. It should be replaced with a brand new one that is the same size, voltage, and specification as the original. When replacing the battery on the key fob remove the metal clips and make sure that the contacts on the key fob are in good condition and free of corrosion.
If the key fob was exposed to water (such as rain or soapy tap water), it is recommended to remove and clean the chip with an electronic cleaner or isopropyl ethanol before installing a new battery. The chip may be permanently damaged by water. If the key fob isn't working after replacing the battery, it could be necessary to replace the key fob.
Faulty Receiver Module
If your key fob has stopped working after replacing the battery and it did not help, or if it suddenly stopped working in a sudden manner it is possible that your receiver module could have developed an issue. The receiver module takes the radio frequency signals from your key fob's remote and transforms them into electrical signals which are then acted upon by other modules within the car.
If the receiver module is faulty it will not take any commands from your remote key fob. In this situation, a dealer will need to reprogramme your key fob, and also install the new receiver.
The key fob is sealed with rubber to prevent water from leaking into the electronic chip. If you dip the key fob in soapy or salty water, it could damage the chip. If your key fob doesn't function, you can try cleaning the chip using isopropyl or electronic cleaner.
If the keys have been successfully paired, but your receiver module is malfunctioning You can try to restart all the electronics in the board by disconnecting the battery with 12 volts for a couple of minutes. Connect the battery in reverse (negative cable to positive first). This will reset the on-board electronic and restore their functionality.
Electronic Chip Faulty
The key fob is outfitted with a tiny chip that transmits a signal from the key to the receiver module every time the key is used. If the signal does not match the one the car has stored the immobilizer will turn off and prevent the vehicle from starting. However, if the key fob is not working and you can't reprogram it this could be due to a faulty chip.
The chip in the key fob may have to be replaced in order to get it working again. The best way to do this is by removing the key from its housing and using a pin needle to contact each of the metal retaining clips. You will need to replace these in the event of damage or corrosion-prone. Make sure that any replacement batteries have the same size, voltage and specifications as the original.
The Seat Alhambra is a popular and well-designed car but like any other car, it can sometimes experience issues with certain parts or equipment. For example there are owners who have had problems with the automatic climate control system, which can malfunction and cause problems in one particular setting. Similarly, the infotainment system has also been reported to malfunction and freeze screens.